MOOSE OFFROAD 0430-0062 Front Inner / Outer Tie Rod End Kit — Polaris Phoenix Kawasaki Bayou Suzuki ATV

MOOSE OFFROAD — Premium High-Tensile Forged Steel Construction, Heavy-Duty Front Inner or Outer Wear-Resistant Steering Joints, and Exact Factory Geometry Precision for Polaris, Kawasaki, Suzuki, and Arctic Cat Utility & Sport ATV Steering Shafts

Restore tight, predictable, and laser-accurate steering control to your four-wheeler with the heavy-duty MOOSE OFFROAD 0430-0062 Front Inner/Outer Tie Rod End Kit. Punishing off-road acceleration, maneuvering through tight wooded trails, and working across deep mud or rugged rocky pastures place intense mechanical stress on an ATV's steering linkage. This is especially true across a massive multi-brand legacy of working utility and sport platforms, including the Polaris Phoenix 200, Kawasaki Bayou 220/250/300/400 and Prairie 300/400, Suzuki Eiger 400, Vinson 500, Ozark 250, and QuadSport, as well as Arctic Cat 90, 350, and 425 series. Over time, factory internal ball joints develop excessive play from harsh trail impacts, heavy water intrusion, and grease breakdown, resulting in a loose handlebars feel, unsafe front wheel wobble, and uneven tire tread wear. This premium-grade replacement kit swaps out worn, sloppy steering joints on either the inner or outer front positions with a beefed-up structural design engineered to withstand brutal off-road feedback.

Every component in this robust steering hardware kit is manufactured from premium high-tensile steel to ensure maximum resistance against bending, shearing, and structural deformation during hard trail impacts, heavy property hauling, or aggressive riding. Designed as a direct drop-in factory replacement, this comprehensive kit includes two high-quality tie rod ends—featuring one left-hand thread and one right-hand thread—complete with all necessary replacement cotter pins and jam nuts for a seamless installation. Built with specialized internal ball-and-socket configurations that manage intense axial and radial steering loads, these tie rod ends deliver ultra-smooth articulation without binding through full suspension travel. Packed with high-grade protective rubber dust boots to seal out fine silt, sand, mud, and water, this steering overhaul kit ensures your quad tracks straight through the toughest terrain.

• Heavy-Duty Forged Steel: High-density structural composition provides immense yield strength to handle punishing trail impacts.
• Complete Thread Set: Includes one left-hand thread and one right-hand thread tie rod end along with fresh jam nuts and cotter pins for a total installation.
• Eliminates Handlebar Slop: Replaces worn, loose ball joints to eliminate dangerous high-speed front-end wheel wobble and steering drift.
• OEM Dimensional Matching: Precision-cut internal threads allow a seamless fit directly onto your factory inner and outer tie rod shafts.
• Protective Seal Booting: Heavy-duty rubber boots keep clean lubrication sealed inside while locking out water, mud, and abrasive grit.
• Inner or Outer Universal Fitment: Versatile engineering allows this kit to service either the front inner position or front outer position on the steering configuration of your quad.

Moto-House MX Pro Tip:

Worn out tie rod ends are more than just a nuisance—they are a major safety hazard on a working utility ATV. If a worn joint shears completely off while you are navigating a tricky technical trail, hauling a heavy load on the property, or pinning the throttle down a straightaway, you instantly lose all steering control over that front wheel. Installation Tip: When removing your old inner or outer tie rod end, count the exact number of full rotations it takes to unscrew it from the rod, or measure the thread distance with a digital caliper. Thread the new Moose tie rod end on using those precise measurements to keep your front-end alignment close to factory specs. Post-Install Protocol: Always perform a proper front-wheel toe-in alignment check once everything is bolted up to prevent tire scrub and aggressive darting. Ordering Note: These kits are sold in sets to complete one full tie rod assembly link (one side); if you want to completely overhaul both the left and right front steering configurations on your quad, you will need to purchase two kits total.

Kit Components	Material Engineering	Chassis Category
2 Tie Rod Ends (1 Left-Hand, 1 Right-Hand Thread)	High-Tensile Heavy-Duty Forged Steel	ATV / 2WD & 4x4 Utility, Youth & Sport Series
Includes Jam Nuts & Cotter Pin Hardware	Heavy-Duty Inner Ball & Socket Layout	Polaris Phoenix / Kawasaki Bayou / Suzuki Eiger, Vinson / Arctic Cat
Weight: 0.59 lbs	Abrasion-Resistant Protective Dust Boots	Direct Drop-In OEM Replacement Geometry

FAQ Questions

Q) Does this single box include components to fix both sides of the front end?
A) No. This kit includes the necessary components to service one single tie rod assembly link (one side). Since an ATV requires a total of two tie rod linkages across the front steering system (left and right), you will need to purchase two kits total to complete a full front steering system overhaul.

Q) Will this tie rod end fit with my aftermarket upgraded heavy-duty tie rod shafts?
A) This kit is engineered to match standard factory OEM thread pitches and shaft dimensions. If your aftermarket upgraded tie rods utilize factory-sized replacement ends, this kit will fit perfectly; if they utilize larger oversized heavy-duty thread links, a proprietary end may be required.

Moto-House MX – Choice of Champions – is located in Clermont/Montverde, FL. We are the best shop in Central Florida with lightning-fast shipping.